Data/Hora: quinta mar 28, 2024 8:22 pm

Os Horários são TMG [ DST ]




Criar Novo Tópico Responder a este Tópico  [ 4 mensagens ] 
Autor Mensagem
 Assunto da Mensagem: Caixas de pregos
MensagemEnviado: quinta abr 03, 2014 2:57 pm 
Desligado
Experiente
Avatar do Utilizador

Registado: sexta mar 13, 2009 1:23 pm
Mensagens: 944
Localização: Alcochete
Entretenham-se com estes esclarecimentos.
Isto é História.
A História dos barulhos das caixas de velocidades que incomodam tantos e já deixaram de incomodar tantos mais.
Enfim...

"Bitter reproaches for the new BMW R 850 R in MO 11/95. Tester Guenter Wimme addressed the issue of shifting behavior unequivocally: "In the old BMW tradition the great weakness remains: the gearbox. Difficult shifting, long shift lever travel, graunchy shifts between first and second, and still the old tale of woe in finding first at stoplights."

In that article's conclusion, our (MO's) journalist Wimme recommended that the BMW factory seek out a new transmission manufacturer. As we now find out, shortly after the introduction of the R 1100 RS, BMW was actually in the process of looking... The Bavarians had already contacted gearbox builders in Japan, Italy and Austria. But after ongoing testing of the prototype proposals the source will remain where it has been since 1978: at Getrag in Ludwigsburg, or more precisely, at the Getrag subsidiary, ZWN in Neuenstein/Hohenloh.

Understandably, the people at Getrag don't like hearing the reproach that they can't build a decent transmission for the prestigious BMW bike, all the moreso since the 3,000 workers of the factory supply the cream of the international automakers with their gearboxes. The list is exceptional: Porsche, Maserati, Alfa Romeo, Alpina Bi-turbo, Jaguar, Ford Cosworth, Dodge Stealth...

Nevertheless, BMW's new boxers don't come close to delivering the same standard of gear-changing that has been set by comparable machines such as Honda's ST 1100. What is the dirty secret here?

O-RINGS AS NOISE-SUPPRESSORS
A clamor of complaints arose together with the introduction of the new Boxer generation. The clattering noises emanating from the hot gearboxes drove more than just those with delicate hearing back to the dealerships in swarms. Gearboxes were replaced in large numbers, and the public rapidly seized on the image of time-bomb gearboxes. (lit. -"Kaputt-guaranty").

In fact, Getrag had built a faultless transmission according to their contract, which, through a chain of circumstances derived from the unique technical characteristics (of the BMW motorcycle), created an acoustical nightmare (lit. "defektbombe").

Analyzed in detail, the truth of the story is revealed. A peculiarity of BMW motorcycle design is that as in an automobile, the transmission is separate from the engine, isolated in its own housing. Between the motor and transmission is the single-plate dry clutch. A characteristic of this design is that transmission noises can clearly be differentiated. In normal Japanese engine architecture the motor and transmission share a common housing. The noises emanating from cam drive, alternator, pistons and transmission blend together, making it difficult to assign exact sources to to the component sounds. The chorus of transmission noises become a section of the overall symphony of mechanical noise.

Motor and transmission castings on the new Boxer are manufactured by a pressure die casting process, which produce a thin-walled housing. Delicate, thin-walled die castings do not block noise as effectively as the somewhat coarser, thicker-walled sand castings (...as formerly used by BMW ÔÇö translator's note). The actual source of the annoying gearbox clatter is the gear teeth themselves, as the flanks of the freewheeling gear teeth click against each other, accelerated by by the uneven rotation of the crankshaft. Imagine that you are a piston. Unlike an electric motor, which revolves in a continuous and even rate, the individual rotations of a piston-driven motor are characterized by a series of accelerations and decelerations. The sparkplug fires, "paff", and the piston and connecting rod thrust hard against the crankshaft, which accelerates. Then the piston reaches bottom dead center, losing energy, as simultaneously the cam chain encounters the resistance of the valve springs, which induces a small deceleration in the rate of the crankshaft's rotation.

At steady, small throttle openings (as in neutral/idle ÔÇö translator's note) and at minimal combustion pressures (power output) this variation in rotational speed is especially noticeable, moreso as the new BMW boxer is programmed to run at very lean, environmentally optimal mixtures. The resulting surges in rotational speed send a shaking effect through the input shaft to the gear cluster. This is what generates the gearbox rattle in neutral, which is all the more apparent when the transmission is hot and the oil is thin.

Faced with substantial numbers of customer complaints, BMW had to react quickly. To dampen the clatter the Bavarians resorted to the introduction of rubber o-rings in the gearbox. These were installed between the transmission shafts and the inner diameters of the freewheeling gears. By this simple trick the disengaged gears are always under a slight drag and cannot spin freely on the transmission shafts, their teeth cannot chatter so easily against one another and the noise is noticeably reduced.

For a self-respecting transmission manufacturer to need to take such a step is something of a fiasco. The efficient operation of the transmission diminished by the o-rings, and the shiftability also suffers.

However, it happens that the noisy rattling in neutral is also an issue in modern, emissions-optimized automobiles. The manufacturers have resolved the problem with a so-called double-mass flywheel, which dampens the torsional fluctuations before they can reach the transmission input shaft. Such a flywheel cannot be used in the BMW boxer motor, as it would be too heavy and might have durability problems withstanding the higher revs of a motorcycle motor.

Thus BMW customers of the future will find o-rings in the gearboxes of all the new BMWs, in spite of the fact that the noisy transmissions of the first ('94) series, with the exception of the objectionable neutral noises, were in fact the better-shifting transmissions. These early transmissions, in point of fact, had no pattern of mechanical defects, only an unattractive noise in neutral when the gearbox was hot.

WHEN FIRST GEAR WON'T ENGAGE....
The light turns green, you pull in the clutch and step on the shift lever of our brand-new Boxer. It doesn't snick into first, it makes no "clack"...On the dash the big neutral "0" still shows on the digital gear indicator and first gear just won't go in. The "hard cases" just keep standing on the pedal and let the clutch out slowly; the more delicate riders go back to neutral, let the clutch back out and start the process over.

How do you suppose the BMW automobile developers would react if they were told that the new top-of-the-line 7-series BMW sedans would only go into first gear only 50% of the time? Of course, they would say, "Guys, get your tails right back to the drawing boards!".

So why did things turn out as they did with the new BMW Boxer? A condition of the contract with Getrag was "No noise when first gear is engaged!" Thus Getrag allowed a "roll-down" time with the clutch pulled in of .8 seconds at operating temperature (note: the time necessary for the free-spinning gears to idle down to a standstill ÔÇö translator's note). After the introduction of the anti-rattle update, the roll-down time was reduced by the increased internal friction of the o-rings to only .4 seconds. Thus the transmission gears spin down to a standstill very quickly. If the opposing gears have not stopped in just the right position, it is very difficult for the shift dogs to find engagement in their intended slots. Result: the gear will not engage.

This BMW characteristic is made yet more noticeable by the use of a perfectly disengaging dry clutch. Unlike Japanese motorcycles using a multi-plate oil bath clutch (which always "drags" a little when disengaged ÔÇö translator's the BMW uses an automotive dry clutch (made by Sachs), which disengages totally, without any clutch drag at all. Thus the BMW clutch provides optimal declutching.

The Japanese transmission, even with the clutch pulled in, is still under continuous rotation from the dragging clutch plates. The result: first gear engages effortlessly. The disadvantage: epecially when it is cold and the oil is thick, first gear engagement is often accompanied by a terrible grinding noise in many motorcycles. And that is exactly what BMW wanted to avoid.

CLANKS AND CRUNCHES
Shifting a BMW transmission requires great concentration. In practice it is a good habit to maintain preload on the shift lever for a moment or two after each shift. Thus one is assured that the gears remain in engagement. This is especially important when starting off and when making the leap from first to second. In general the BMW transmission, even in the higher gears, shifts notchily and unwillingly.

The Getrag engineers have an illuminating explanation for this characteristic as well. The BMW designers required a minimum of freeplay between rotating parts in the gearbox, so that the "driveline slop", eagerly criticized by magazine testers, would be reduced as much as possible. Minimal rotational play, however, results in more difficult shifting. This is easy to visualize, as the smaller the clearance between the shift dogs on one gear and their respective openings in the mating gear, the more difficult it becomes to find the optimal position for engagement.

To banish this blemish the Getrag designers developed a two-tiered (stepped) shift dog. The slightly extended, narrower tip of the shift dog easily engages the (now relatively large) opening in the facing gear. When the gears have turned just a little more, the entire shift dog now slides into the engagement slot.

If a neophyte Boxer owner just nudges the shift lever and feels the tip of the shift dog drop in, it may seem as if the shift has been completed successfully. However, it may happen that under load the gear jumps back out of engagement. The seasoned BMW gear-banger, by keeping the pedal under preload, can feel both the first and second stage of complete engagement take place. Subjectively, the impression the transmission makes is "notchiness".

Loud clanks and bangs have been inherent in BMW transmissions since the beginning of time. These noises have always been especially "robust" when shifting down from second to first gear. This BMW peculiarity is best explained by the basic mechanical characteristics of the gearbox. The mass of the three-shaft transmission (input shaft w/torsion damper & spring, intermediate cluster & output shafts ÔÇö translator's note) and large diameter dry clutch inevitably carries a great deal of rotational energy. There are also rather large relative differences in the ratios and speeds of the gears in the lower ranges and at low rpms. Finally, the solid shaft drive system does nothing to dampen the impact of the gears' engagement.

Thus, the current situation... The question remains: who is guilty of creating this miserable transmission? On one hand it would seem that the bulk of the answer lies buried in the conceptual foundations of the Bavarian Boxer. Tradition is often good for Marketing but not necessarily best when dealing with matters of functionality. On the other hand, the example of BMW/ Getrag shows what can happen when two partners are not sufficiently engaged in communication during the development process... The alloted time suddenly runs out; the World Introduction inexorably arrives, and the dealers, gnashing their teeth, are left to whitewash the shortcomings as best they can. It is lucky that in spite of this the customers are convinced by BMW's offering and continue to buy Bavarian with unbridled enthusiasm.



SIDEBARS

1. IN THE PLANS: IMPROVEMENTS TO THE BOXER TRANSMISSION

In the planning stages: high load roller bearings with fine-particle oil filtration (clean bearings) will replace the previously specified barrel roller bearings on the input shaft. By this means the previously reduced (through the introduction of the o-rings) roll-down time will be increased to approximately 1 second. This will make engaging first gear from a standstill easier.

Simple shift dogs with slightly increased engagement clearance will replace the stepped shift dogs. The transmissions of the K models have always been equipped with this shift dog design. This measure will improve the shifting haracteristics.

BMW has recognized that the rider likes to hear an acoustical signal that first gear has been engaged. In the future even a BMW will generate a little noise and produce a perceptible commotion through the shift lever when first gear is engaged. It will all of course be of the highest and most satisfying quality.

To this end a new dry clutch is being developed with a carefully defined amount of clutch drag when disengaged. This measure will bring the engagement of first gear from a standstill up to the appropriate standard.

Further detail work on the transmission will make the o-rings superfluous.

The mentioned modifications will be introduced in series production up through the model year 1997.

2. CONVERSATION WITH GETRAG/ZWN

Transmission-Questions: What the builders say. MO spoke to Getrag development engineers Klaus Sommer and Eberhard Schaetzle. Both ride their own privately-owned BMWs. Sommer a K 1100 RS and Schaetzle the new R 1100 GS.

MO: Are the transmissions of the R models similar to those of the K models, broadly speaking?
SOMMER: There exists similarity in concept only. For example the gear ratios, shift mechanism and engagement dogs are different on the K model, and the K model even has a different housing.
MO: Can Getrag-ZWN look back on other motorcycle experience besides BMW?
SOMMER: At Getrag some time ago we manufactured the Yamaha XS 750 shaft drive system, which was designed by Porsche.
MO: Getrag produces these transmissions at considerable expense. Forexample the highest-loaded 5th gearset is finely honed to produce the best possible surface on the flanks of the teeth. The rest of the gears are shaved. Do these transmissions still need to be broken in?
SCHAETZLE: Every fully asssembled transmission goes onto a test stand and is thoroughly tested with hot test-oil. Afterwards the hot oil is extracted and along with it the first wearing-in material.The transmission does not need to be broken in. It can be be fully loaded from the very beginning.
SOMMER: After the first rides, the o-rings in the boxer gearboxes settle in a little. Then the transmission may shift a little easier. This has nothing to do with wearing in. Only the braking effect of the o-rings is slightly lessened. After sufficient operation and with a hot motor a slight ticking noise in neutral can be audible even with an o-ring transmission. This ticking will be louder when the idle synchronization is not meticulously adjusted.
MO: What kind of oil recommendation for the BMW transmission can you give us?
SCHAETZLE: Oil should be seen as an integral part of the transmission. When designing the transmission the load bearing capability of the oil is part of the calculation. We fill the BMW transmissions with SAE 90 GL 5 gear oil manufactured by Fuchs, a brand mainly found as an OEM supplier.
SOMMER: SAE 90-Oil should be used throughout the whole year. It istrue that in winter the shifting will suffer at first from the thick oil, but it should improve during a very short ride. For those to whom this is disturbing, because they make many short trips, for example, can use 75w90 GL 5 in winter as an alternative. In summer it must be changed back to SAE 90 GL 5.
MO: How do you regard oil additives?
SCHAETZLE: Oil additives are always factors which cannot be taken into account when designing and building a transmission. In the best case they don't do any harm. For example, it has not been researched yet how oil additives might react with the new "clean bearings". We therefore rigorously recommend against their use, especially in automotive transmissions. Synchro rings, for example, function only if they can exert some braking effect on the gear wheels. Special extra-slippery additives can result in big damages."


Share on FacebookShare on TwitterShare on Google+
Topo
 Perfil Enviar Mensagem Privada  
 
 Assunto da Mensagem: Re: Caixas de pregos
MensagemEnviado: sexta abr 04, 2014 10:43 pm 
Desligado
Admin.
Avatar do Utilizador

Registado: domingo fev 10, 2008 1:32 am
Mensagens: 2078
Localização: Massamá
Pois eh Leonel...
O calcanhar de Aquiles da marca Bávara, para muitos.... :)

_________________
RICARDO MATIAS
K1200LT-99
R1200GS-12


Topo
 Perfil Enviar Mensagem Privada  
 
 Assunto da Mensagem: Re: Caixas de pregos
MensagemEnviado: quarta jun 04, 2014 11:58 pm 
Desligado
Rookie
Avatar do Utilizador

Registado: terça jul 23, 2013 5:20 pm
Mensagens: 28
Localização: Pegões
Não é defeito, é mesmo feitio. Nas embraiagens a seco metam FAHER e vão ver que melhora e muito. :-)


Topo
 Perfil Enviar Mensagem Privada  
 
 Assunto da Mensagem: Re: Caixas de pregos
MensagemEnviado: quinta jun 05, 2014 9:28 am 
Desligado
Experiente
Avatar do Utilizador

Registado: sexta mar 13, 2009 1:23 pm
Mensagens: 944
Localização: Alcochete
J. Lopes Escreveu:
Não é defeito, é mesmo feitio. Nas embraiagens a seco metam FAHER e vão ver que melhora e muito. :-)


Para os motores com embraiagem banhada a óleo, têm um procedimento adequado.
Com as embraiagens a seco, podes meter no motor e na caixa. Tudo bem.
No motor poderá ter as vantagens anunciadas de redução do atrito, mas na caixa...

"SCHAETZLE: Oil additives are always factors which cannot be taken into account when designing and building a transmission. In the best case they don't do any harm. For example, it has not been researched yet how oil additives might react with the new "clean bearings". We therefore rigorously recommend against their use, especially in automotive transmissions. Synchro rings, for example, function only if they can exert some braking effect on the gear wheels. Special extra-slippery additives can result in big damages."

Quem usar, diga qualquer coisa.


Topo
 Perfil Enviar Mensagem Privada  
 
Mostrar mensagens anteriores:  Ordenar por  
Criar Novo Tópico Responder a este Tópico  [ 4 mensagens ] 

Os Horários são TMG [ DST ]


Quem está ligado:

Utilizadores a ver este Fórum: Nenhum utilizador registado e 12 visitantes


Criar Tópicos: Proibido
Responder Tópicos: Proibido
Editar Mensagens: Proibido
Apagar Mensagens: Proibido
Enviar anexos: Proibido

Ir para:  
cron
Desenvolvido por phpBB® Forum Software © phpBB Group
Traduzido por phpBB Portugal